Mercury 225 EFI Скачать руководство пользователя

Страница: 408 / 719

COOLING

90-884294 OCTOBER 2001

Page 4B-9

Troubleshooting

Thermostat Test

1. Inspect thermostat covers and cylinder head covers (thermostat opening) for cracks and

corrosion damage that could cause leakage. Replace parts as necessary.

2. Remove and discard gasket from each thermostat.

3. Wash thermostats with clean water.

4. Using a thermostat tester, similar to the one shown, test each thermostat as follows:

a. Open thermostat valve, then insert a thread between valve and thermostat body. Al-

low valve to close against thread.

b. Suspend thermostat (from thread) and thermometer inside tester so that neither

touches the container. Bottom of thermometer must be even with bottom of thermo-
stat to obtain correct temperature of thermostat opening.

c. Fill thermostat tester with water to cover thermostat.

d. Plug tester into electrical outlet.

e. Observe temperature at which thermostat begins to open. (Thermostat will drop off

thread, that was installed in Step “a”, when it starts to open.) Thermostat must begin
to open when temperature reaches 140

-145

F (60

-63

C).

Continue to heat water until thermostat is completely open.

g. Unplug thermostat tester.

h. Replace thermostat, if it fails to open at the specified temperature, or if it does not

fully open.

NOTE: BE SURE that water in thermostat tester is allowed to cool sufficiently [below 110

(43.3

C)] before testing the other thermostat.

51087

IMPORTANT: DO NOT operate engine without thermostats installed.

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды

Mercury 225 EFI, Руководство по обслуживанию

Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды