Mercury 225 EFI Скачать руководство пользователя

Страница: 388 / 719

POWERHEAD

Page 4A-76

90-884294 OCTOBER 2001

Powerhead Installation On Driveshaft Housing

1. Install Lifting Eye (91-90455) into flywheel.

WARNING

BE SURE that Lifting Eye is threaded into flywheel a minimum of five (5) turns BE-
FORE lifting powerhead.

2. Using a hoist, lift powerhead high enough to allow removal of powerhead from repair

stand. Remove powerhead from repair stand, being careful not to damage drive shaft
housing gasket surface of powerhead.

3. Place a new gasket around powerhead studs and into position on base of powerhead.

IMPORTANT: DO NOT apply lubricant to top of driveshaft as this will prevent drive-
shaft from fully engaging into crankshaft.

4. Apply a small amount of 2-4-C Marine Lubricant with Teflon onto driveshaft splines.

NOTE : Verify shift shaft is properly installed in gearcase/driveshaft housing before instal-
ling powerhead.

5. Use hoist to lower powerhead onto driveshaft housing. It may be necessary to turn fly-

wheel (aligning crankshaft splines with driveshaft splines) so that powerhead will be fully
installed.

59076

a -

Lifting Eye (90-90455)

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды

Mercury 225 EFI, Руководство по обслуживанию

Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды