Mercury 225 EFI Скачать руководство пользователя | Manualshive

Страница: 14 / 719

background image

MAINTENANCE

90-884294 OCTOBER 2001

Page 1B-5

9. Stop engine, turn water off and remove flushing attachment from gear housing.

IMPORTANT: While and after flushing, keep outboard in upright position until all wa-
ter has drained from drive shaft housing to prevent water from entering the power-
head via drive shaft housing and exhaust ports.

Fuel System

WARNING

Avoid serious injury or death from gasoline fire or explosion. Carefully follow all
fuel system service instructions. Always stop the engine and DO NOT smoke or
allow open flames or sparks in the area while servicing any part of the fuel sys-
tem.

Before servicing any part of the fuel system, stop engine and disconnect the battery. Drain
the fuel system completely. Use an approved container to collect and store fuel. Wipe up
any spillage immediately. Material used to contain spillage must be disposed of in an ap-
proved receptacle. Any fuel system service must be performed in a well ventilated area.
Inspect any completed service work for sign of fuel leakage.

Fuel Line Inspection

Visually inspect the fuel line and primer bulb for cracks, swelling, leaks, hardness, or other
signs of deterioration or damage. If any of these conditions is found, the fuel line or primer
bulb must be replaced.

IMPORTANT: Visually inspect for fuel leakage from the filter connections by
squeezing the primer bulb until firm, forcing fuel into the filter.

Water Separating Fuel Filter – EFI Models

NOTE: The warning system will turn on when water in the fuel filter reaches the full level.

1. This filter removes moisture and also debris from the fuel. If the filter becomes filled

with water, the water can be removed. If the filter becomes plugged with debris, the
filter must be replaced with a new filter.

a

59030

a -

Fuel/Water Separator Filter

Remove and replace filter as follows:

2. Turn ignition key switch to OFF position.

3. Disconnect wire at bottom of filter.

«
...
12
13
14
15
16
...
»

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

Бренд: Barco Страницы: 54

Бренд: nord Страницы: 91

Бренд: ZAFFER Страницы: 28

Бренд: Wisconsin Motors Страницы: 46

Бренд: Hoval Страницы: 12

Бренд: Toyama Страницы: 48

Air-injection 50 cc

Бренд: APRILIA Страницы: 33

Бренд: Toyota Страницы: 525

Бренд: Volvo Penta Страницы: 64

Бренд: Volvo Penta Страницы: 104

SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198

Бренд: TJERNLUND Страницы: 14

Бренд: TJERNLUND Страницы: 27

Бренд: Electric Drive Engineering Страницы: 19

Бренд: Just Motion Control Страницы: 21

Бренд: O.S. engine Страницы: 11

Бренд: Honda Страницы: 193

Бренд: Yanmar Страницы: 6

NEWTON ACM EUROTITAN CL

Бренд: Xl Automatismos Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды