manualshive.com logo in svg

Mercury 225 EFI, Руководство по обслуживанию

Меркурий 225 EFI - великолепный мотор для лодки, обеспечивающий отличную мощность и производительность. Для обслуживания и ремонта необходимо скачать бесплатный сервисный мануал на manualshive.com. Этот руководство поможет вам ухаживать за вашим мотором и поддерживать его в отличном состоянии.

Поделиться
Скачать
background image

RIGHT HAND NON-RATCHETING

Page 6A-62

90-884294   OCTOBER 2001

2. Install a dial indicator and align the dial indicator pointer so that it is perpendicular to

and touching the “I” mark on the dial indicator tool. Tighten the indicator tool onto the
drive shaft and rotate the drive shaft so that the needle in the dial makes at least one
full revolution and comes to “0” on the dial indicator scale.

57939

a

b

c

d

a

e

f

a -

Nuts (4) (Obtain Locally)

b -

Threaded Rod [3/8 in. (9.5mm) obtain locally]

c -

Dial Indicator Holding Tool (91-83155)

d -

Dial Indicator (91-58222A1)

e -

Indicator Pointer

f -

Backlash Indicator Rod (91-53459) (for 1.75:1)
Backlash Indicator Rod (91-78473) (for 1.87:1 ratio)

3. Take the backlash readings by lightly turning the drive shaft back and forth, so as to

feel the backlash between the gears, (no movement should be noticed at the propeller
shaft).

a. Observe the dial indicator and record the reading.

b. Loosen the indicator tool and rotate the drive shaft 90 degrees in a clockwise di-

rection.

c. Repeat step 2 above and take and record another reading. Repeat step 3 until a

total of 4 backlash readings have been taken.

4. Add the four readings together and divide the sum by four. This is your average back-

lash and it should be 0.030 in. - 0.050 in. (0.76mm - 1.27mm) (for 1.75:1 and 1.87:1
ratios). If backlash is not as indicated, gear case is not properly assembled or parts
are excessively worn and must be replaced before returning gear case to service.

5. Loosen the backlash indicator tool and remove the propeller nut, washer and pinion

nut adaptor. Remove the dial indicator and all its mounting components. Do not re-
move the bearing preload tool. The following instructions give specific instruc-
tions for its removal.

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

Wartsila 31 Product Manual preview
31
Бренд: Wartsila Страницы: 168
E-Z-GO Engine Shop Rebuild Manual preview
Engine
Бренд: E-Z-GO Страницы: 100
HunterDouglas M40 TE Instructions And Warnings For Installation And Use preview
M40 TE
Бренд: HunterDouglas Страницы: 20
Kubota D722-E3B Workshop Manual preview
D722-E3B
Бренд: Kubota Страницы: 138
M.T.H. E-8 DIESEL ENGINE Operating Instructions Manual preview
E-8 DIESEL ENGINE
Бренд: M.T.H. Страницы: 36
Golen Jeep Six-Cylinder Setup Manual preview
Jeep Six-Cylinder
Бренд: Golen Страницы: 11
E-Z-GO 295cc Shop Rebuild Manual preview
295cc
Бренд: E-Z-GO Страницы: 112
Vascat MAC-HS4 Series Operation And Maintenance Manual preview
MAC-HS4 Series
Бренд: Vascat Страницы: 9
Beninca YAK 20 OM 115 Manual preview
YAK 20 OM 115
Бренд: Beninca Страницы: 72
DELTA DORE TYMOOV 10RE2 Quick Start Manual preview
TYMOOV 10RE2
Бренд: DELTA DORE Страницы: 16
Yaroslavl Engine Plant YMZ-536 Operation Manual preview
YMZ-536
Бренд: Yaroslavl Engine Plant Страницы: 168
Mercury/Mariner 25 MARATHON Manual preview
25 MARATHON
Бренд: Mercury/Mariner Страницы: 130
Mercury VesselView 4 Operation And Maintenance Manual preview
VesselView 4
Бренд: Mercury Страницы: 18
Mercury 240 Jet Drive Manual preview
240 Jet Drive
Бренд: Mercury Страницы: 9
Mercury 92-8M0069603 Operation & Maintenance Manual preview
92-8M0069603
Бренд: Mercury Страницы: 85
MerCruiser 305 CID (5.0L) Service Manual preview
305 CID (5.0L)
Бренд: MerCruiser Страницы: 895
Kohler KG2204 Service preview
KG2204
Бренд: Kohler Страницы: 108
Festo EMMS-ST-28-L Series Operating Instructions preview
EMMS-ST-28-L Series
Бренд: Festo Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды