manualshive.com logo in svg

Mercury 225 EFI, Руководство по обслуживанию

Меркурий 225 EFI - великолепный мотор для лодки, обеспечивающий отличную мощность и производительность. Для обслуживания и ремонта необходимо скачать бесплатный сервисный мануал на manualshive.com. Этот руководство поможет вам ухаживать за вашим мотором и поддерживать его в отличном состоянии.

Поделиться
Скачать
background image

ATTACHMENTS / CONTROL LINKAGE

Page 7-10

90-884294   OCTOBER 2001

Ride Guide Steering Cable/Attaching Kit Installation
(92876A9)

Dual Cable - Dual Outboard

WARNING

Quicksilver Super Ride-Guide Steering (dual cables) MUST BE USED with this at-
taching kit. Failure to adhere to this requirement could result in steering system
failure.

Refer to “Quicksilver Accessories Guide” to determine correct length of steering cable
and remote control cables.

IMPORTANT: Steering cable and remote control cables MUST BE THE CORRECT
LENGTH, sharp bends on too-short cables result in “kinks”; too-long cables re-
quire unnecessary bends and/or loops. Both conditions place extra stress on the
cables and reduce the performance of the steering system.

Installation Requirements

IMPORTANT: The distance from each outboard’s centerline to the side of transom
opening MUST BE a minimum of 16 in. (406 mm).

This kit contains all necessary parts to connect both outboards to Ride-Guide Steering
Cables for 23-1/2 in. thru 27-1/2 in. (597 mm thru 699 mm) outboard centerline spacing.
If outboard centerline distance is other then specified, refer to end of this instruction man-
ual for optional extension couplers.

DETERMINE ROUTING OF STEERING CABLES

Use “1” or “2”, following, to route steering cables:

1. Parallel cable routing: Cables routed together down starboard side of boat Refer to

“Parallel Routed Steering Cables and Attaching Kit Installation,” immediately
following.

2. Opposite side cable routing: One cable routed down starboard side of boat and one

cable routed down port side of boat. Refer to “Opposite Side Routed Steering
Cables and Attaching Kit Installation,” located on page 18 of this instruction manu-
al.

CAUTION

With this kit installed, the upper (outboard) mounting bolts MUST BE installed so
that hex head end of bolts is on the inside of boat transom, as illustrated. Failure
to install upper mounting bolts, as shown in illustration, could result in interfer-
ence between steering cable nut and ends of mounting bolts when outboard is
tilted up.

Install upper bolts so that hex head end of bolts is on the inside of boat transom.

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

O.S. engine MAX-46AX Instruction Manual preview
MAX-46AX
Бренд: O.S. engine Страницы: 4
Westerbeke FOUR-60 Technical Manual And Parts List preview
FOUR-60
Бренд: Westerbeke Страницы: 140
R.A. Lister SR4 Instruction Book & Parts Catalogue preview
SR4
Бренд: R.A. Lister Страницы: 84
TIS TIS-TM120 Installation Manual preview
TIS-TM120
Бренд: TIS Страницы: 12
ROJ PCS W1 Installation, Operation And Maintenance Manual preview
PCS W1
Бренд: ROJ Страницы: 60
Hatz 2G40 Operator'S Manual preview
2G40
Бренд: Hatz Страницы: 94
Grizzly H5384 Instruction Sheet preview
H5384
Бренд: Grizzly Страницы: 2
Leadshine iSV-B23 Series Hardware Installation Manual preview
iSV-B23 Series
Бренд: Leadshine Страницы: 18
Lombardini LGA 226 Use & Maintenance preview
LGA 226
Бренд: Lombardini Страницы: 64
Lombardini 11LD522-3 Series Workshop Manual preview
11LD522-3 Series
Бренд: Lombardini Страницы: 44
Lombardini 8LD600-2 Workshop Manual preview
8LD600-2
Бренд: Lombardini Страницы: 58
Lombardini 11 LD 535-3 Workshop Manual preview
11 LD 535-3
Бренд: Lombardini Страницы: 68
Lombardini 9 LD 561-2 Use And Maintenance preview
9 LD 561-2
Бренд: Lombardini Страницы: 109
Ozroll ODS T10 Manual preview
ODS T10
Бренд: Ozroll Страницы: 7
Yanmar 2YM15 Service Manual preview
2YM15
Бренд: Yanmar Страницы: 231
Yanmar BY series Installation Manual preview
BY series
Бренд: Yanmar Страницы: 33
DANA 4360-58 Parts List preview
4360-58
Бренд: DANA Страницы: 3
DANA 4360-53 Parts List preview
4360-53
Бренд: DANA Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды