Mercury 225 EFI Скачать руководство пользователя

Страница: 718 / 719

225/250/3.0 Litre Work EFI Water Flow 2002 Model Year

1. Water Inlet

2. Water Pump

3. Wall of Water - If water level height is insufficient, water pump may draw in air resulting in an overheated

engine

4. Strainer - Exhaust cooling water

5. Main Water Feed to Powerhead from Water Tube

6. Rubber Water Dams - If missing may result in uneven cooling of cylinders and scuffed pistons

7. Cylinder Head Cover - Removed from head for illustration, normally part of head casting

8. Thermostats (2) 143

F (61.7

C) - If stuck closed, engine will overheat at low speed. If stuck open,

engine will not warm up at idle speed.

9. Poppet Valve - Controls water flow at high RPM. If poppet valve is stuck open at low RPM, the engine

will not reach proper operating temperature (run cold) and will run rough at idle

10. Primary water discharge into driveshaft housing.

11. Water discharge into exhaust relief passage

12. Water Pressure Sensor

13. Check Valve for powerhead flush

14. Water passing through thermostats dump into adaptor plate, then discharges down the exhaust.

15. Tell-Tale Outlet

16. Excess water from wall of of water around exhaust bucket exits around anodes.

17. Water Exits with Exhaust Discharge

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды

Mercury 225 EFI, Руководство по обслуживанию

Результаты поиска

Содержание 225 EFI

Отзывы:

Похожие инструкции для 225 EFI

Бренды по названию

Популярные бренды