Mercury 225 EFI Скачать руководство пользователя | Manualshive

Страница: 561 / 719

background image

RIGHT HAND NON-RATCHETING

Page 6A-70

90-884294 OCTOBER 2001

Gear Lubricant Filling Instructions

1. Inspect “Fill” and “Vent” sealing washers for cuts or abrasions. Replace washers if

necessary.

2. Clean any metal debris from magnet on “Fill” plug.

IMPORTANT: Never apply lubricant to gear housing without first removing Vent
screw, or gear housing cannot be filled because of trapped air. Fill gear housing
ONLY when housing is in a vertical position.

3. Slowly fill housing thru Fill hole with Premium Gear Lubricant until lubricant flows out

of “Vent” hole and no air bubbles are visible.

4. Install Vent screw into Vent hole.

IMPORTANT: DO NOT lose more than one fluid ounce (30cc) of gear lubricant while
reinstalling Fill screw.

5. Remove grease tube (or hose) from Fill hole and quickly install Fill screw into Fill hole.

Installing Gear Housing to Driveshaft Housing

WARNING

Disconnect high tension leads from spark plugs and remove spark plugs from
engine before installing gear housing onto driveshaft housing.

1. Tilt engine to full up position and engage the tilt lock lever.

2. Apply a light coat of 2-4-C Marine Lubricant with Teflon onto driveshaft splines.

CAUTION

DO NOT allow lubricant on top of driveshaft. Excess lubricant, that is trapped in
clearance space, will not allow driveshaft to fully engage with crankshaft. Subse-
quently, tightening the gear housing nuts (while excess lubricant is on top of dri-
veshaft) will load the driveshaft/crankshaft and damage either or both the power-
head and gear housing. Top of driveshaft is to be wiped free of lubricant.

3. Apply a light coat of 2-4-C Marine Lubricant with Teflon onto shift shaft splines. (DO

NOT allow lubricant on top of shift shaft.)

4. Apply a thin bead of G.E. Silicone Sealer against the top of divider block.

5. Insert trim tab bolt into hole in rear of gear housing to driveshaft housing machined

surface.

6. Shift gear housing into NEUTRAL and place guide block anchor pin into NEUTRAL

position

Right Hand Rotation Outboard

Forward Gear

Reverse Gear

a

a -

Guide Block Anchor Pin

7. Position gear housing so that the driveshaft is protruding into driveshaft housing.

«
...
559
560
561
562
563
...
»

Содержание 225 EFI
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 EFI

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

Бренд: EuroLite Страницы: 19

Бренд: Perkins Страницы: 92

Бренд: SEW-Eurodrive Страницы: 88

Бренд: Vedeneyev Страницы: 381

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 22

Бренд: Sears Страницы: 12

Бренд: Baumr-AG Страницы: 25

Бренд: Toro Страницы: 96

Бренд: Volvo Страницы: 8

Бренд: O.S. engine Страницы: 21

max-12TZ series

Бренд: O.S. engine Страницы: 41

Бренд: Tomahawk Страницы: 20

BLACK DEVIL PRO

Бренд: Cors-Air Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды