MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 3

Страница: 3 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

4.2 Settings IP Interface without Secure

........................................................................................... 24

4.2.1 General

................................................................................................................................. 24

4.2.2 IP Configuration

................................................................................................................... 25

4.3 Example of assigning IP addresses

.............................................................................................. 26

4.4 KNX Multicast Address

.............................................................................................................. 27

4.5 Main line

...................................................................................................................................... 28

4.6 Sub line

........................................................................................................................................ 30

4.7 Communication settings

.............................................................................................................. 32

4.7.1 Procedure ETS 4

................................................................................................................... 32

4.7.2 Procedure ETS 5

................................................................................................................... 34

4.7.3 Set tunneling connections

..................................................................................................... 35

4.7.3.1 Procedure for IP Router without Secure

........................................................................ 35

4.7.3.2 Procedure for IP Router with Secure

............................................................................. 36

5 Parameter –> E-Mail Client

............................................................................................................... 37

5.1 General Settings

.......................................................................................................................... 37

5.1.1 General

................................................................................................................................. 37

5.1.2 Web Interface

....................................................................................................................... 38

5.1.3 Time/Date

............................................................................................................................. 39

5.2 E-Mail Functions

......................................................................................................................... 40

5.2.1 Status elements

..................................................................................................................... 40

5.2.2 Bit Alarms

............................................................................................................................ 42

5.2.2.1 Macros

........................................................................................................................... 43

5.2.3 Text Alarms

.......................................................................................................................... 44

5.2.4 Status Reports

....................................................................................................................... 45

5.2.5 Specific behavior and error handling

................................................................................... 46

5.3 Overview Communication Objects

............................................................................................. 47

5.4 Secure Group Address Communication

...................................................................................... 48

6 Web-Interface

..................................................................................................................................... 49

6.1 Call of the Web-Interface

............................................................................................................ 49

6.2 Overview Web-Interface

............................................................................................................. 50

6.3 Settings of E-Mail functionality

.................................................................................................. 51

6.4 E-Mail – Error codes & remedy

.................................................................................................. 54

6.5 Receive E-Mail as push message

................................................................................................ 54

6.6 Receive E-Mail as SMS

.............................................................................................................. 54

Содержание SCN-IP000.03


























































Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды

MDT Technologies SCN-IP000.03, Техническое руководство

Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды