MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 25

Страница: 25 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

4.2.2 IP Configuration

The following parameters can be set in the submenu "IP Configuration":

Figure 14: Settings – IP Configuration (without Secure)

The following table shows the setting options for this submenu:
ETS-Text

Dynamic Range

[Default value]

Comment

HTTP Port



8080

Specifying of the http port

DHCP



use



not in use

Setting whether the IP address should be
assigned automatically via DHCP or
manually be set in further submenus

The following settings are displayed for "Do not use DHCP”
IP-address

(0-255).(0-255).(0-255).(0-255)

0.0.0.0

IP-address of the router



only with manual IP address
assignment

Net mask

(0-255).(0-255).(0-255).(0-255)

0.0.0.0

Subnet mask of the network



only with manual IP address
assignment

Gateway

(0-255).(0-255).(0-255).(0-255)

0.0.0.0

Gateway-address of the network



only with manual IP address
assignment

DNS

(0-255).(0-255).(0-255).(0-255)

0.0.0.0

Domain Name Server of the network



only with manual IP address
assignment

Table 4: Settings – IP Configuration (without Secure)

Содержание SCN-IP000.03


























































Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды

MDT Technologies SCN-IP000.03, Техническое руководство

Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды