MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

7

7

Green

Red

LED 1
Bus State - LAN

Off: LAN Error
On: LAN OK

On: Manual Mode active

LED 2
Bus State - KNX

Off: KNX Bus: Error or not connected
On: KNX Bus OK

LED 3
Traffic - LAN

Flashing: Bus load at LAN-side
Off: No Bus load at LAN-side
Speed up to 10 Mbit/s

Flashing: Transmission error at LAN
side

LED 4
Traffic - KNX

Flashing: Bus load at KNX side
Off: No Bus load at KNX side

Flashing: Transmission error at KNX
side

LED 5
Forwarding of
group telegrams

Forwarding of group telegrams
- Off: LAN and KNX different
- Filter table activ

Lock

Green and Red: forwarding all

LED 6
Forwarding of
physical addresses

Forwarding of physical addresses
- Off: LAN and KNX different
- Filter table activ

Yellow: Lock

Green and Yellow: forwarding all

Table 1: Overview LEDs

2.5 Commissioning without Data Secure

The following procedure is recommended for commissioning the SCN-IP100.03:

1.

Insert the application „SCN-IP000.03 – KNX IP Router“

2.

Configuration of the IP-Router:

3.

Transfer of the physical address and the application of the IP Router. For this, the
programming button must be

pressed shortly

. The programming LED

lights steadily red

.

4.

After successful transfer of the physical address and the application, the red LED turns off
again.

5.

Insert the application „SCN-IP000.03 – KNX IP Router with email function“

6.

Configuration of the E-Mail Client:

7.

Transfer of the physical address and the application of the E-Mail Client. For this, the
programming button has to be

pressed long

. The programming

LED flashes red

.

8.

After successful transfer of the physical address and the application, the red LED turns off
again.

9.

Accessing the Web client to configure the e-mail addresses by opening an Internet browser
and call the address: http:\\IP address: port, for example: http: \\192.168.1.178:8080 for the
IP address 192.168 .1.178 and the http port 8080

Important:

If the IP address of the IP Router gets changed subsequently, the device must perform a

reboot. This restart is not performed automatically by the application programming in the ETS4/5.
Here, a manual restart will be required, which either by right-clicking on the device and selecting
"Reset device" is executed or a short removing of the bus connector.

«
...
5
6
7
8
9
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Бренд: Watchguard Страницы: 40

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

OfficeConnect 3C19500

Бренд: 3Com Страницы: 52

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: ?omtime Страницы: 62

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

Бренд: Allied Telesis Страницы: 22

Бренд: Watchguard Страницы: 30

Бренд: Lanner Страницы: 59

Бренд: NETGEAR Страницы: 142

Бренд: Quantum Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды