MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

24

24

MAC Address

Specified by the unit.

Multicast Address

The multicast address is specified by the backbone and can be changed in the project in the tab
"Topology Backbone".

Commissioning Password

Set the start-up password (optional), see also “3 Safety – IP Secure/Data Secure”.

Authentication Code

Specify the authentication code (optional), see also “3 Safety – IP Secure/Data Secure”.

4.2 Settings IP Interface without Secure

4.2.1 General

The following parameters can be set in the "General" submenu:

Figure 13: General Settings (without Secure)

The following table shows the setting options for this submenu:
ETS-Text

Dynamic Range

[Default value]

Comment

Host name (30 signs)

any

[MDT KNX IP Router]

Any name can be chosen here, but it
should be as meaningful as possible.

Enable slow
connections



enable



disable

Adjust the timeout for tunneling
connections. By default, slow connections
are not supported and a short timeout is
used for the UDP connection. This can be
increased by supporting slow connections
which may be necessary especially for
tunnel connections over the internet.

Fallback time for
manual operation



10 min



1 hour



4 hours



8 hours

Setting of the automatic release time
from manual mode to automatic mode

Manual function



disabled



pass all telegrams



pass physical telegrams



pass group telegrams

Defines the behavior after manual
changeover

Table 3: General Settings (without Secure)

«
...
22
23
24
25
26
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Бренд: Dahua Страницы: 24

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

Бренд: NEC Страницы: 2

Бренд: Airlink101 Страницы: 46

Бренд: Accton Technology Страницы: 78

Бренд: Tripp Lite Страницы: 34

Бренд: LevelOne Страницы: 3

EdgeRouter ER-8

Бренд: Ubiquiti Страницы: 20

Бренд: Altimium Страницы: 12

Security Router X-PeditionTM

Бренд: Enterasys Страницы: 466

Бренд: ENKHO Страницы: 48

ROADRECORDER 8400 NVR

Бренд: Safety Vision Страницы: 27

Бренд: CTC Union Страницы: 12

Бренд: Ubiquiti Страницы: 13

WRT330N - Wireless-N Gigabit Gaming Router Wireless

Бренд: Linksys Страницы: 92

Бренд: MikroTik Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды