background image

 

 

Technical Manual – IP Router  SCN-IP100.03

 

 

 

MDT technologies GmbH  •  

51766 Engelskirchen  •  Papiermühle 1

 

 

Tel.: +49-2263-

880  •  Fax: +49-2263-4588  •  [email protected]  •  www.mdt.de 

53

 

 

53

 

 
In addition to the above described vendor web.de, the following providers are tested with the 
settings listed below: 

gmx.de 

SMTP server address:   mail.gmx.net 
SMTP server port: 

587 

1&1 

SMTP server address:   smtp.1und1.de 
SMTP server port: 

587 

Telekom 

SMTP Server address:  smtpmail.t-online.de 
SMTP server port: 

465 

HotMail, now outlook.com/de 

SMTP server address:  smtpmail.live.com 
SMTP server port: 

587 

Strato 

SMTP server address:  smtp.strato.de 
SMTP server port: 

587 

 
All data of the email providers are on the state of the manual, see front page, and are not 
guaranteed. 
 
Into the “Destination E-mail address” insert all email addresses (max. 3) to which you want to send 
an email. 
Then you close the menu by the OK button. 
In the following menu the e-mail configuration can be tested: 

 

Figure 42: Web Interface – Destination E-Mail Test 

After successful configuration, a test e-mail to the set destination addresses can be triggered. 
Then the status is displayed and if so, an error is displayed. The significance of the error codes is 
shown in 6.4 E-Mail – Error codes & remedy 
 

 

Test E-Mail Address 1 

Status 

Содержание SCN-IP000.03


























































Отзывы: