MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

50

50

6.2 Overview Web-Interface

After calling up the web interface, the login window appears:

Figure 37: Web Interface – Login window

After a successful login, the menus can be selected on the left side. The menus have the following
functions:



Device Info

The menu “Device Info” contains information and settings of the IP Router, such as MAC
address, IP address, network settings, software version, etc.



Prog.Mode

In the menu “Prog. Mode” the programming LEDs for the TP and the IP side can be switched
ON and OFF. Furthermore, the allocated physical addresses, the tunneling addresses and
serial number can be seen.



Email

In the menu “Email” the e-mail functionality can be set, see also 6.3 .



Time

In the menu “Time”, information concerning the time server can be viewed.



Firmware Update

It is possible to perform a firmware update for the IP Router.
For more information see 2.7 Firmware Update.
If you have any questions, please contact MDT Support at

[email protected]

«
...
48
49
50
51
52
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

Бренд: 3Com Страницы: 50

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

ipRocketLink 3086FR

Бренд: Patton electronics Страницы: 12

Бренд: Maipu Страницы: 26

AlterPath Manager 2500

Бренд: Cyclades Страницы: 368

Бренд: Alcatel-Lucent Страницы: 60

Бренд: Modecom Страницы: 16

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Бренд: 3Com Страницы: 12

Бренд: NetComm Страницы: 65

DotSurfer GPC-2100

Бренд: Gtran Wireless Страницы: 44

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды