MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 42

Страница: 42 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

5.2.2 Bit Alarms

Up to 10 "Bit Alarms" can be activated.
The figure below shows the available settings (here at the example of Bit alarm 1):

Figure 31: Settings – Bit Alarm

The following table shows the settings available for an activated Bit alarm:
ETS-Text

Dynamic range

[Default value]

Comment

Text for E-Mail

Any text, alternatively use of macros
(see 5.2.2.1 Macros)

Setting of the text to be
displayed in the email

Send behaviour



send at ON



send at OFF



send at change to ON or OFF



send at change to ON



send at change to OFF

Setting when the e-mail should
be sent

Send email to destination
address 1



yes



Setting whether to send to
recipients 1

Send email to destination
address 2



yes



Setting whether to send to
recipients 2

Send email to destination
address 3



yes



Setting whether to send to
recipients 3

Table 16: Setting options – Bit Alarm

The table below shows the available communication objects:

Number

Name

Length

Usage

Bit Alarm 1

1 Bit

Triggering the first alarm bit

next Bit alarm

Table 17: Communication objects – Bit Alarm

Содержание SCN-IP000.03


























































Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды

MDT Technologies SCN-IP000.03, Техническое руководство

Результаты поиска

Содержание SCN-IP000.03

Отзывы:

Похожие инструкции для SCN-IP000.03

Бренды по названию

Популярные бренды