MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

32

32

4.7 Communication settings

If the IP configuration of the KNX Router is valid, the device can be used as an interface to KNX EIB.
Therefore, connect the IP Router to the KNX bus and the network.

4.7.1 Procedure ETS 4

Attention: In ETS4 only the application "without Secure" can be used. Data Secure is only
supported from ETS 5.7.2 on!

Select the menu „Communication“ in the folder „Settings“:

Figure 18: Settings ETS4 – Communication

Here the IP Router should be listed in the “Discovered connections”:

Figure 19: Settings ETS4 – Discovered connections

«
...
30
31
32
33
34
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: IBM Страницы: 32

Бренд: NETGEAR Страницы: 2

Бренд: Oracle Страницы: 24

Бренд: TP-Link Страницы: 110

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: Talent Страницы: 18

Бренд: ActiveEye Страницы: 35

Бренд: Tripp Lite Страницы: 3

Бренд: Gbord Страницы: 11

Бренд: Vector Страницы: 8

Бренд: Tenda Страницы: 70

Бренд: Planet Страницы: 67

Бренд: LAWO Страницы: 68

Бренд: Axis Страницы: 10

Бренд: Honeywell Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды