Makita DRC300, Инструкция по эксплуатации, Страница: 32 / 480

29 ENGLISH
Number
Cause Action
Notified problem
E04X
Error of the side brushes
Is foreign matter such as lint or hair caught in the side brushes? Remove foreign matter.
See pages 13 and 25.
E060
Non -detection of the dust
box or the filter
The dust box or the filter is not attached. Check that they are attached properly.
See pages 21 and 24.
E09X
Cliff sensor error
Is the robotic cleaner exposed to direct sunlight? Move the robotic cleaner to another place.
See page 10.
Is the robotic cleaner on a black floor surface?
Are the cliff sensor dirty?
• Gently wipe off the dirt on the cliff sensor with a dry, soft cloth,
a cotton swab, etc.
• Check if the earthing line contacts to the ground.
See pages 8 and 10 and 27.
E10X
Bumper sensor error
It is a malfunction of the bumper sensor. Press the bumper with your hand about 10 times.
→ See page 8.
E110
Motion error
Does the robotic cleaner run on a step, etc. and get stuck there? Move the robotic cleaner to another place.
See page 10.
E12X
Decrease in the
remaining battery
capacity
Timer setting error
Is the robotic cleaner unable to start operating by ON timer
reservation because the remaining battery capacity is
insufficient?
When starting operation by ON timer reservation, make sure that
the batteries are fully charged.
E140
Room setting error
Location information error
Is the room different from the mapped room, or is the starting
point of cleaning different?
Check the mapped room and the starting point of cleaning.
See page 17.
Is the layout of the mapped room changed? Perform mapping again.
See page 16.
Is the LiDAR sensor blocked by a cloth or dirty? Remove the cloth, etc., and care for the LiDAR sensor.
See page 27.
Are there any obstacles with a height of 25 cm or more that the
LiDAR sensor can detect around the robotic cleaner?
The LiDAR sensor requires obstacles taller than 25 cm within
the following ranges:
• 11 m radius from the robotic cleaner for mapping and mapping
cleaning mode.
• 18 m radius from the robotic cleaner for free cleaning mode.
Please place some obstacles taller than 25 cm in the area.
E170
Error of the robotic
cleaner top cover
Is the top cover of the robotic cleaner open? Close the top cover of the robotic cleaner.
E190
Error due to loss of a
wheel or uplift of the
robotic cleaner
Is a drive wheel derailed, or is a wheel separated from the
ground?
Move the robotic cleaner to another place.
See page 10.
E200
Error due to failure to
return back to the starting
point
Error due to failure to go
to the destination
The robotic cleaner failed to return back to the starting point of
cleaning.
• If there are objects that obstruct the running of the robotic
cleaner, put the objects away or keep the robotic cleaner away
from those objects.
See page 20.
• If robotic cleaner frequently fails to return to the starting point,
turn on [Prioritize Homing] on the app. The time taken to go
back to the starting point can be longer.
See page 42.
• Check if there is a pathway of 80 cm or more for cleaning.
The robotic cleaner failed to proceed to the next destination
because it is entered a narrow passage.
Troubleshooting
Before asking for repair or making an inquiry, check whether the following apply.
Power supply
Symptom Cause Action
• Pressing the start/stop button does
not turn on the power.
• The lamp does not light up.
• Pressing buttons on the robotic
cleaner and the remote control
results in no response.
Are the batteries installed correctly? Check for proper installation of the batteries.
See page 14.
Is the battery capacity lost? Check the remaining capacity.
Is the power of the robotic cleaner turned off? Press the start/stop button of the robotic cleaner to turn on the
power.
See page 15.