Magnum Energy ME-AGS-N Скачать руководство пользователя

Страница: 82 / 103

10.0 Using the ME-RTR Router

METER: 03A AGS Status Menu

This read-only menu displays the AGSs current status. There are 26 differ-
ent status messages to identify what state the AGS is currently in only one

displays at any one time (refer also to Figure 10-2).

METER: 03B DC Volts-AGS Menu

This read-only menu displays the DC voltage measured at Terminals #3 and

#4 of the AGS module. This menu is useful in setting up the voltage start for
the AGS, and for troubleshooting its operation.

Info:

The DC voltage reading in this menu may vary from the DC

voltage readings in the METER buttons

01A DC Volts

and

04C DC

Volts-BMK

menus. When troubleshooting, read the appropriate re-

lated meter for each device. When troubleshooting the AGS, use the

03B DC Volts-AGS

menu for veri



cation and testing purposes.

Available statuses are (see Tables 11-1 thru 11-3 for information on each):

Info:

This menu is important when determining if the AGS is work-

ing correctly, or for troubleshooting an AGS installation. For any
fault mode displayed in the status menu, refer to Section 12.0 in

this manual.

METER: 03C Gen Run Time Menu

This read-only menu displays the length of time the generator has been
running since it was autostarted by the AGS. This is useful when trying to

determine how long the generator has been running since it was autostarted
in case you were not present when it started. This menu is enabled when

the

CTRL: 03 Gen Control

menu is set to

AUTO

, but does not display run

time when the generator has been manually started. Cooldown and warm-up

times are not included in this gen run time display.

AC In

Gen Cooldown

Gen Warm-up

Manual Run

No Comm

Off

Quiet Time

Ready

Start Amp

Start Exercise

Start SOC

Start Temp

Start Test

Start Time

Start Topoff

Start VDC

Gen Run Fault

Fault Amp

Fault Exercise

Fault MaxRn

Fault SOC

Fault Temp

Fault Test

Fault Time

Fault Topoff

Fault VDC

Info:

The

Gen Run Time

menus timer is started when the gen run

sense voltage/signal is correct and quali



ed at the AGS module. It is

not considered quali



ed until after a full start attempt and the

Gen

Warm-up Time

setting is satis



ed. Cooldown and warm-up times are

not included in the gen run time display. Total generator run time =

Gen Run Time

Gen Warm-up Time

Gen Cooldown

Info:

The times in this display are shown in tenths of an hour (0.0

hrs., 0.1 hrs., etc.,) thus, 0.1 hrs. = 6 minutes.

Info:

The Gen Run Time display resets to 0.0 each time the genera-

tor is autostopped. This meter is not designed to replace the hour
meter for total hours the generator has run.

Содержание ME-AGS-N








































































































Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды

Magnum Energy ME-AGS-N, Руководство пользователя

Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды