Magnum Energy ME-AGS-N Скачать руководство пользователя

Страница: 61 / 103

9.0 Using the ME-ARC Remote

METER: 03B DC Volts-AGS Menu

This read-only menu displays the DC voltage measured at Terminals #3 and
#4 of the AGS module. This menu is useful in setting up the voltage start for

the AGS, and for troubleshooting its operation.

METER: 03E Since Gen Run (Days) Menu

This read-only menu displays the number of days since the generator has
last run. This is useful in determining if the start and stop settings are set

up correctly. This timer begins once the

CTRL: 03 Gen Control

menu is set

AUTO

, and then counts by 1 for every 24-hour period the generator does

not start. The Days Since Run timer resets any time the generator starts,
which could be either by autostarting the generator (including from a previ-

ous exercise run), or manually starting the generator.

Info:

When the DIP switch inside the AGS is set to 2-Wire Standby

Mode, if you do not use the ME-ARC to manually turn the generator

on, the Days Since Run timer will not be reset to zero.

Info:

The

Gen Run Time

menus timer is started when the gen run

sense voltage/signal is correct and quali



ed at the AGS module. It is

not considered quali



ed until after a full start attempt and the

Gen

Warm-up Time

setting is satis



ed. Cooldown and warm-up times are

not included in the gen run time display. Total generator run time =

Gen Run Time

Gen Warm-up Time

Gen Cooldown

Info:

The times in this display are shown in tenths of an hour (0.0

hrs., 0.1 hrs., etc.,) thus, 0.1 hrs. = 6 minutes.

Info:

The

Gen Run Time

display resets to 0.0 each time the genera-

tor is autostopped. This meter is not designed to replace the hour

meter for total hours the generator has run.

Info:

This display is used by the

SETUP: 04F Max Gen Run Time

menu to determine the generators maximum run time when start-
ed automatically.

METER: 03D AGS Temp Menu

This read-only menu displays the temperature of the AGS remote temp sen-
sor (included with AGS, but use optional), and is helpful in determining its

proper placement and operation. This temperature value can be displayed
in either Fahrenheit or Celsius depending on the

SETUP: 01E Temp Display

setting. Use this menu to change the temperature format, if required.

METER: 03C Gen Run Time Menu

This read-only menu displays the length of time the generator has been run-

ning since it was autostarted by the AGS. This helps determine how long the
generator has been running in Auto mode if you were not present when it

started. This menu is enabled when

CTRL: 03 Gen Control

is set to

AUTO

, but

does not display run time when the generator has been manually started.

Cooldown and warm-up times are not included in the gen run time display.

Info:

The DC voltage reading in this menu may vary from the DC

voltage readings in the METER buttons

01A DC Volts

and

04C DC

Volts-BMK

menu items. When troubleshooting, read the appropriate

related meter for each device. When troubleshooting the AGS, use

the

03B DC Volts-AGS

menu for veri



cation and testing purposes.

Содержание ME-AGS-N








































































































Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды

Magnum Energy ME-AGS-N, Руководство пользователя

Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды