Magnum Energy ME-AGS-N Скачать руководство пользователя

Страница: 92 / 103

11.0 ME-AGS-N Remote Status Messages

Table 11-2, AGS Remote Start Statuses

STATUS

REMOTE

DESCRIPTION

Start Amp

ARC/RTR

The generator has started based on the

SETUP:

04C Gen Run Amps

setting.

Start
Exercise

ARC/RTR

The generator has started based on the

SETUP:

04H Gen Exercise

setting.

Start SOC

ARC/RTR

The generator has started based on the

SETUP:

04D Gen Run SOC

setting.

Start

Temp

The generator has started based on the

AGS: 04

Start Temp

setting.

ARC/RTR

The generator has started based on the

SETUP:

04E Gen Run Temp

setting.

Start Test

RC/ARC/

RTR

The AGS is in Test mode. Test mode may be

started from the TEST button located on the
AGS,

or, by selecting

Test

from the

AGS: 01 AGS

Control

menu (see Section 5.1 for further infor-

mation on the AGSs TEST button).

Start Time

ARC/RTR

The generator has started based on the

SETUP:

04B Gen Run Time

setting.

Start

Topoff

ARC/RTR

The generator has started based on the

SETUP:

04G Quiet Time Topoff Time

setting.

Start VDC

The generator has started based on

AGS: 05

Start Volts

setting.

ARC/RTR

The generator has started based on

SETUP: 04A

Gen Run VDC

setting.

11.2 AGS Remote Start Statuses

The following Start statuses identify the condition that autostarted the
generator. If you determine that the autostart condition occurred sooner

than expected (or didnt want this autostart condition), refer to the Setup
section for your speci



c remote to change (or defeat) the autostart setting.

Содержание ME-AGS-N








































































































Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды

Magnum Energy ME-AGS-N, Руководство пользователя

Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды