Magnum Energy ME-AGS-N Скачать руководство пользователя

Страница: 90 / 103

11.0 ME-AGS-N Remote Status Messages

A status message may be an operational or fault message. Access the AGS
status menu (METER buttons

03A AGS Status

menu for ME-ARC and ME-

RTR; AGS buttons

02 AGS Status

menu for ME-RC) to view the AGSs cur-

rent operating status. This menu is important when determining if the AGS

is working correctly, or for troubleshooting an AGS installation.

11.1 AGS Remote Operational Statuses

Refer to Table 11-1 for a brief description of the possible AGS operational
statuses that may display (depending on your remote).

Note:

RC = ME-RC, ARC = ME-ARC, and RTR = ME-RTR

STATUS

REMOTE

DESCRIPTION

Ready

The

AGS: 01 AGS Control

menu is set to

Enable

or to

Enable w/QT

, and the AGS is ready to au-

tomatically start the generator based on the AGS

buttons active autostart settings.

ARC/RTR

The

CTRL: 03 Gen Control

menu is set to

AUTO

and the AGS is ready to automatically start the

generator based on the active autostart settings
under the

SETUP: 04 AGS Setup

menu.

No Comm

RC/ARC/
RTR

The AGS is not communicating with the inverter/
remote.
This is a normal status if there is no AGS (Net-

work version) connected in the system.
If an AGS is installed, then refer to Section 12.2

Resolving Operational Statuses for assistance.

AC In

RC/ARC/

RTR

The inverter/charger is connected to another

source such as a grid or an alternate generator,
and is not controlled by the AGS. When

AC In

displays, the AGS is prevented or locked out from
all autostarting conditions, except for when the

generator needs to exercise if enabled.

Off

The

AGS: 01 AGS Control

menu is set to

Off

. This

setting will not allow the AGS to autostart the
generator.

ARC/RTR

The

CTRL: 03 Gen Control

menu is set to

OFF

This setting will not allow the AGS to autostart
the generator.

Gen

Cooldown

ARC/RTR

The autostop setting has been satis



ed in one

of the generator autostart/autostop menus, and

the generator has been disconnected from the
inverter/charger. However, the generator is still

running until the cooldown time is met (as per
the

SETUP: 04J Gen Cooldown Time

setting).

Table 11-1, AGS Remote Operational Statuses

Содержание ME-AGS-N








































































































Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды

Magnum Energy ME-AGS-N, Руководство пользователя

Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды