Magnum Energy ME-AGS-N Скачать руководство пользователя

Страница: 97 / 103

12.0 ME-AGS-N Remote Troubleshooting

• Fault Test

The generator failed to autostart and run after

Test

selected under the

AGS: 01 AGS Control

menu in the ME-RC, or the red

TEST button is pressed on the AGS module (using any remote).

Note:

The ME-ARC and ME-RTR do not provide a test selection, in-

stead they can be set to manually turn the generator on and off, which
can be used to test the generator wiring to the AGS.

• Fault VDC

The generator failed to autostart and run per the

05 Start

Volts

(ME-RC) or the

04A Gen Run VDC

(ME-ARC & ME-RTR) menus

start parameters.

• Fault Amp

The generator failed to autostart and run per the

04C Gen

Run Amps

(ME-ARC & ME-RTR only) menus start parameters.

• Fault Exercise

The generator failed to autostart and run per the

04H

Gen Exercise

(ME-ARC & ME-RTR only) menus start parameters.

• Fault SOC

The generator failed to autostart and run per the

04D Gen

Run SOC

(ME-ARC & ME-RTR only) menus start parameters.

• Fault Time

The generator failed to autostart and run per the

04B Gen

Run Time

(ME-ARC & ME-RTR only) menus start parameters.

• Fault Topoff

The generator failed to autostart and run per the

04G

Quiet Time Topoff

(ME-ARC and ME-RTR only) start parameters.

Remedy:

One of the above fault messages may display on the remote

control when:
A. The AGS attempts to start the generator four times, but the gen

failed to start and run per the speci



c autostart parameters; or,

B. The generator started, but did not provide the correct gen run
sense signal to the AGS module. For either scenario, refer to Section

6.2 to troubleshoot why the generator does not start or run.

• Fault MaxRn

The generator has turned off because the gen run time

after autostarting has exceeded the

SETUP: 04F Max Gen Run

Time

setting (ME-ARC and ME-RTR only).

Info:

The

Max Gen Run Time

menu uses the

SETUP: 04B Gen Run

Time

display to determine the generators run time. Cooldown and

warm-up times are not included in the

Gen Run Time

display.

Remedy:

Con



rm that all the autostop parameters that are active or

enabled can be satis



ed before the

SETUP: 04F Max Gen Run Time

setting is reached.
If using the

SETUP: 04A Gen Run VDC

menus parameters:

with a battery voltage setting to autostop, ensure the auto-
stop voltage is less than the temperature-compensated absorb

charge voltage.
with the

Float

setting to autostop, ensure the time that the

charger is in the Bulk Charge and Absorb Charge

stages is shorter

than the

04F Max Gen Run Time

setting.

Refer to your remotes

SETUP: 04A Gen Run VDC

section for ad-

ditional information on this setting.

Note

Several conditions determine the length of time that

the charger is in the Absorb Charge stage. Ensure the SETUP:

03E Absorb Done (Time, Amps, or SOC) setting determines
when the Absorb Charge stage is complete and enters the Float

stage is taken into account when setting the 04F Max Gen
Run Time setting.

Содержание ME-AGS-N








































































































Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды

Magnum Energy ME-AGS-N, Руководство пользователя

Результаты поиска

Содержание ME-AGS-N

Отзывы:

Похожие инструкции для ME-AGS-N

Бренды по названию

Популярные бренды