Magnum Energy ME-AGS-N Скачать руководство пользователя | Manualshive

Страница: 29 / 103

background image

23

© 2012 Magnum Energy, Inc.

6.0 ME-AGS-N Module Troubleshooting

6.0 ME-AGS-N Module Troubleshooting

6.1 Using the ME-AGS-N’s LED Indicators

The two LEDs on the front of the AGS controller indicate how the AGS is
operating and help you troubleshoot the AGS system. The STATUS LED is bi-

color (green or red) and indicates the AGSs status. The READY LED is green,
and lights if the AGS has power and the remote temp sensor is connected.
The AGS controller performs a self test when power is



rst applied. The

green READY LED lights up (solid) and the STATUS LED blinks green once. If
the self-test is successful, test the AGS system for proper operation by press-

ing and releasing the TEST button. The STATUS LED blinks green, and the
AGS should start the generator. Once the generator starts, the STATUS LED

lights solid green and the generator runs for approximately 30-60 seconds,
and then shuts off (will not try to restart within the next two minutes). If the

generator does not start and stop as expected, refer to Table 6-1 below to
help



nd a solution.

WARNING:

Completely unplug the green 8-port terminal block from

the AGS module before performing maintenance on the electrical or
generator system to prevent harm to servicing personnel.

LED

Indication

Symptom

Solution

STATUS is on red
= Gen fault

1. Gen wont start; or
2. Gen wont run. It

starts, but is stopped
by the AGS (B+ or gen

run sense voltage not
sensed to Terminal
#2).

Refer to Section 6.0 ME-AGS-N Module
Troubleshooting for assistance.
Unplug/remove and reconnect the green

8-port friction-



t terminal block to reset

the STATUS (fault) indicator.

STATUS is blinking
green = Gen start

initiated

Gen start initiated.

No problem normal operation.

STATUS is on solid

green = Gen run

Gen is running.

No problem normal operation.

READY is off =

No power con-
nected to the AGS

module

DC voltage to Termi-

nals #3 (+) and #4
(-) on module miss-

ing or incorrect.

1. Check fuse, check DC wiring.

2. Check the DC voltage under the AGS

TECH menu.

READY is blinking

= The tempera-
ture sensor is not
detected

Note:

Temp sen-

sor is not required
to be connected

unless the temp
autostart feature
is needed.

The temp sensor

is not sensed or
plugged into the
purple REMOTE port.

1. Check the temp sensor cable and its

connection to the purple REMOTE port, or

2. Check the temp sensor cable for any

damage.

3. Obtain another temp sensor cable.

4. Check the DC voltage under the AGS
TECH menu.

READY is on
(solid) = Power

and temp sensor
connected

The temp sensor
is connected to the

purple REMOTE port.

No problem normal operation.

Table 6-1, ME-AGS-N Module Troubleshooting Guide

«
...
27
28
29
30
31
...
»

Содержание ME-AGS-N








































































































Отзывы:

Нет отзывов

Похожие инструкции для ME-AGS-N

Бренд: Access Страницы: 12

Бренд: Bartlett Страницы: 5

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: UCS Страницы: 4

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: Sanhua Страницы: 3

Бренд: National Instruments Страницы: 8

Бренд: Oceanic Systems Страницы: 8

Бренд: Rane Страницы: 2

Бренд: Vageo Страницы: 2

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды