Lenovo System x3550 M5 Скачать руководство пользователя страница 374

Страница: 374 / 1144

Retry the operation.

•

4000008a-00000000 : Management Controller [arg1]: Configuration restoration from a file by

user [arg2] failed to start.

This message is for the use case where a user restores a Management Controller configuration from
a file and the restoration fails to start.

May also be shown as 4000008a00000000 or 0x4000008a00000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0138

User Response

1. Turn off the server and disconnect it from the power source. You must disconnect the server

from ac power to reset the IMM.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

Retry the operation.

•

4000008b-00000000 : Storage [arg1] has changed.

This message is for the use case where an IP address for the Storage Management has changed

May also be shown as 4000008b00000000 or 0x4000008b00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - IMM Network event

SNMP Trap ID

360

Lenovo System x3550 M5 Installation and Service Guide

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды