Lenovo System x3550 M5 Скачать руководство пользователя страница 134

Страница: 134 / 1144

Note:

If you need to view any LEDs on the system board or front panel, ensure that you view

the LEDs before disconnect the power cords.

Step 3.

If the server has been installed in a rack, slide the server out from the rack enclosure.

Step 4.

Remember to check if the cover is locked. If it is locked, unlock the cover first.

Latch

Lock

Unlock

Figure 35. Unlocking the cover

Step 5.

Press the blue tab on the cover-release latch and lift up the cover-release latch. Then, slide the
cover to the rear.

Latch

Cover

Figure 36. Cover removal

Step 6.

Lift the server cover off the server and set it aside.

Attention:

For proper cooling and airflow, replace the server cover before you turn on the server.

Replacing the cover

Use this information to replace the cover.

To replace the server cover, complete the following steps:

120

Lenovo System x3550 M5 Installation and Service Guide

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды