Lenovo System x3550 M5 Скачать руководство пользователя страница 287

Страница: 287 / 1144

Step 7.

Remove the microprocessor cover, tape, or label from the surface of the microprocessor socket, if
one is present. Store the cover in a safe place.

Microprocessor

Cover (Keep for future use)

Figure 205. Socket cover removal

Attention:

When you handle static-sensitive devices, take precautions to avoid damage from static

electricity. For details about handling these devices, see “Handling static-sensitive devices” on
page 118.

Step 8.

Close the microprocessor socket release levers and retainer:

Microprocessor

release lever

Microprocessor
release lever

Figure 206. Microprocessor socket levers and retainer engagement

Close the microprocessor retainer on the microprocessor socket.

Identify which release lever is labeled as the first release lever to close and close it.

Close the second release lever on the microprocessor socket.

Step 9.

Install the heat sink.

Chapter 5

Removing and replacing components

273

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды