Lenovo System x3550 M5 Скачать руководство пользователя страница 962

Страница: 962 / 1144

1. If the system was recently installed, moved, or serviced, make sure the battery is properly

seated.

2. Check the Lenovo support site for an applicable service bulletin or firmware update that

applies to this error.

Replace the CMOS battery.

4. (Trained technician only)Replace the system board

948

Lenovo System x3550 M5 Installation and Service Guide

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды