Lenovo System x3550 M5 Скачать руководство пользователя страница 981

Страница: 981 / 1144

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

218-904-000 : Brocade:ExternalEthLoopbackTest Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check or replace SFP/cable.

2. Rerun the test.

3. Verify whether the firmware is at proper level.

4. Rerun the test.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

218-905-000 : Brocade:SerdesEthLoopbackTest Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Rerun the test.

Appendix C. DSA diagnostic test results

967

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды