Lenovo System x3550 M5 Скачать руководство пользователя страница 1084

Страница: 1084 / 1144

•

201-901-003 : Standalone Memory Test Failed

Memory Diagnostics Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

5. Replace any DIMMS(s) mentioned in error, one by one.

6. Make sure that all DIMMs are enabled in the Configuration/Setup Utility program.

7. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory stress test results

The following messages can result when you run the memory stress test.

Test results for the DSA memory stress test

The following messages can result when you run the DSA memory stress test.

•

202-000-000 : MemStr Test Passed

Test Passed.

Recoverable

Severity

Event

1070

Lenovo System x3550 M5 Installation and Service Guide

«
...
1082
1083
1084
1085
1086
...
»

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды