Lenovo System x3550 M5 Скачать руководство пользователя страница 983

Страница: 983 / 1144

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-801-000 : Check-point Panel Test Aborted

Check-point Panel Test Aborted. BMC is unable to verify that the operator information panel cable is
connected.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Inspect and reseat operator information panel cable at both ends.

2. Verify that the Baseboard Management Controller (BMC) is working.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-901-000 : Check-point Panel Test Failed

Check-point Panel Test Failed. Operator reported incorrect display.

Recoverable

Severity

Appendix C. DSA diagnostic test results

969

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды