Lenovo System x3550 M5 Скачать руководство пользователя страница 415

Страница: 415 / 1144

•

80010204-1d06ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 6A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d06ffff or 0x800102041d06ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

Fan 6B Tach :

•

80010204-1d07ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 7A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d07ffff or 0x800102041d07ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

401

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды