Lenovo System x3550 M5 Скачать руководство пользователя страница 1095

Страница: 1095 / 1144

Severity

Event

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-801-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Unable to communicate with driver.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the DSA Diagnostic code is at the latest level.

2. Run the test again.

3. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

4. Run the test again.

5. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

6. Run the test again.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-802-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. A read error was encountered.

Recoverable

Appendix C. DSA diagnostic test results

1081

«
...
1093
1094
1095
1096
1097
...
»

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды