Lenovo System x3550 M5 Скачать руководство пользователя страница 373

Страница: 373 / 1144

This message is for the use case where a user restores a Management Controller configuration from a
file and it completes.

May also be shown as 4000008800000000 or 0x4000008800000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0136

User Response

Information only; no action is required.

•

40000089-00000000 : Management Controller [arg1]: Configuration restoration from a file by

user [arg2] failed to complete.

This message is for the use case where a user restores a Management Controller configuration from a file
and the restoration fails to complete.

May also be shown as 4000008900000000 or 0x4000008900000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0137

User Response

1. Turn off the server and disconnect it from the power source. You must disconnect the server

from ac power to reset the IMM.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

359

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды