Lenovo System x3550 M5 Скачать руководство пользователя страница 1117

Страница: 1117 / 1144

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-905-000 : Tape Test Failed

Tape Test Failed. Software error: invalid request.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system.

2. Check the system firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Make sure that the drive firmware is at the latest level.

6. Run the test again.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-906-000 : Tape Test Failed

Tape Test Failed. Unrecognized error.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

Appendix C. DSA diagnostic test results

1103

«
...
1115
1116
1117
1118
1119
...
»

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды