Labrie MINIMAX Скачать руководство пользователя страница 97

Страница: 97 / 174

Hydraulic System

Adjusting Pressure on Cart Tipper Valve (if installed)

This section describes the procedure for adjusting the cart tipper hydraulic pressure on the tipper
control valve (see Figure 5-17).

Figure 5-17 Tipper control valve

For this procedure, use a 0

- 4000

psi pressure gauge.

To adjust the cart tipper pressure:

Start the engine and engage the hydraulic system.

Remove rubber cover from the quick-connect coupler located on the flow divider (see

Figure

5-18).

Install a 0

- 4000

psi pressure gauge on the quick-connect coupler (see

Figure

5-18).

Push the tipper lever (see Figure 5-17) and hold it while you read the pressure on the gauge.

Check the pressure on the gauge to make sure the pressure builds up in the system.

Set the pressure at idle to 2,000

psi by adjusting the relief valve (see Figure 5-17). To do so,

loosen the locknut of the relief valve and turn the adjustment screw clockwise or
counterclockwise to get the proper pressure.

Once the pressure is adjusted, tighten back the locknut.

Replace rubber cover on the quick-connect coupler (see Figure 5-18).

Lever

Relief valve

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды