Labrie MINIMAX Скачать руководство пользователя страница 60

Страница: 60 / 174

General Maintenance

Repeat the procedure until the limit switch is properly adjusted.

Figure 3-35 Arm extended warning light

Adjusting Arm Parked Limit Switch

Centrally located inside the Helping-Hand

arm assembly,

near the top cover,

the arm parked limit

switch (see Figure 3-36)

sends a signal to the controller module that the automated arm is in parked

travel position inside the hopper and turns off the A

XTENDED

warning light on the dashboard.

To adjust this limit switch, apply the following procedure:

Take down

the grabber completely by using the joystick.

Fully extend the arm.

Turn off the engine.

Proceed with the tagout/lockout procedure. Refer to “Locking Out and Tagging Out the
Vehicle” on page 20.

Danger!

All limit switches MUST be working at all times. Otherwise, the operator may not be aware that
the arm is not fully retracted or that the grabber is open or closed. This may cause an accident,

injuries or property damages

Caution!

This procedure must be done correctly before adjusting the gripper auto-closing system.

Danger!

Do not stand directly in the path of the arm while carrying out these tasks.

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды