Labrie MINIMAX Скачать руководство пользователя страница 100

Страница: 100 / 174

Hydraulic System

Reinstall the access panel, the strainer and the return filter housing.

Reinstall the filler cap and fully open the ball valve.

Start the engine.

Cleaning the Strainer

To clean the strainer:

Empty the hydraulic tank (see

Emptying the Hydraulic Tank

on page 90).

Remove the hose clamp from the suction hose.

Slide the hose over the pipe until it clears the nipple (slide towards the frame of the vehicle).

Remove the strainer from the tank port (see Figure 5-20 and Figure 5-21).

Clean the strainer using solvent, and check for damage; replace if necessary.

Replace the seal if necessary.

Reinstall the strainer.

Using a filtering screen, refill the tank with high-quality oil until it reaches the 3/4

mark on the oil

gauge (see

Recommended Lubricants

on page 57 for specifications).

The entire system will require between 50 and 60

gallons of oil.

Caution!

Failure to open the ball valve may seriously damage the pump and the hydraulic system.

Caution!

It is not recommended to mix different brands and/or grades of oil in the hydraulic tank.

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды