Labrie MINIMAX Скачать руководство пользователя | Manualshive

Страница: 16 / 174

background image

8

Safety

Only qualified personnel

should service the hydraulic, electrical, and pneumatic systems of this vehicle.

They should also be fully versed in operating the vehicle.

General Precautions

It is the employer’s responsibility to ensure that

only

qualified employees operate and maintain this

vehicle.

Read and make sure that you fully understand this manual and all safety decals before performing
maintenance on the vehicle. Maintenance personnel must also read and understand the

Operator

Manual

for this vehicle. In case of doubt, ask a supervisor for clarifications.

Before every work day, inspect the body, the packing system, and any system that might
compromise public and/or operator safety.

Verify that the accelerator pedal, the steering wheel, mirrors, brakes, and turn signals are in good
working order.

When driving the vehicle, keep both hands on the steering wheel at all times.

Stop the vehicle completely and put on the parking brake before leaving the driving position.

When the vehicle is parked, the parking brake

must

be applied.

Vehicle operators must have a clear view of lifting arm operations at all times. To prevent injury to
surrounding people, and damage to property and/or to the lifting arm itself, operators must be
able to stop arm movement at any time.

Before activating the lifting arm, operators shall make sure that people and obstructions are far
away from the vehicle.

M

INIMAX

™ vehicles are primarily designed to be operated

by only one person.

However, if Labrie

Enviroquip Group customers elect to operate the vehicle with more than one worker, additional
safety items shall be installed

to protect the co-worker

from hazardous situations.

I

MPORTANT

:

In such cases, Labrie Enviroquip Group

must be informed

of every and all units that will be operated

by more than one worker. Labrie Enviroquip Group will then determine and supply, at the
customer’s expense, the required safety items. For additional information, please contact Labrie

Plus

at 1-800-231-2771 in the U.S. or 1-877-831-8250 in Canada.

Warning!

Prior to its first use, your M

INIMAX

™

must be completely lubricated

, as shown on the lube

chart located on the curbside of the truck, near the hopper.
Initial lubrication carried out by Labrie Enviroquip Group is sufficient for production and
transport purposes

only!

Danger!

Operator and maintenance personnel must adhere to the following precautions

at all

times.

Failure to do so may result in vehicle and/or property damage, personal injury, or

even death.

«
...
14
15
16
17
18
...
»

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MINIMAX

Бренд: New Holland Страницы: 23

Бренд: New Holland Страницы: 31

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 46

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды