Labrie MINIMAX страница 173 Скачать руководство пользователя

Страница: 173 / 174

Lifting Arm

165

To adjust arm speed:

Lock out and tag out the vehicle (see

Locking Out and Tagging Out the Vehicle

on page 20).

Secure the area around the path of the arm with barrier tape or barricades.

Put the transmission in Neutral.

Start the engine and engage the hydraulic system.

Clearly identify the stopper screw on the valve that corresponds to the proper function (arm
extension/retraction, gripper open/close).

Move the lever to evaluate arm speed, then release the lever.

Make sure the Speed-Up feature is activated. Engine speed should be at 1200

rpm.

Loosen the locknut.

Turn the restrictor adjustment screw only one eighth (1/8th) of a turn at a time to see a
significant change in the arm speed.

Move the lever again to evaluate arm speed. Repeat until cycle times are properly set (see table
below).

10.

Tighten back the locknut.

Danger!

Do not stand in the path of the arm while carrying out these adjustments.

Caution!

When adjusting tilt movement speed, make sure the auto-closing feature allows the gripper
to close sufficiently to avoid gripper fingers hitting the hopper walls.

Table 1

Arm Operating Pressure and Cycle Times (engine speed at 1200

rpm)

Arm function

Pressure setting (psi)

Cycle time (sec.)

Arm extend/retract

2000

10.5

Arm up

2000

Arm down

2000

Gripper close

1200

Gripper open

750

less than 2

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Похожие инструкции для MINIMAX

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Похожие инструкции для MINIMAX

Бренды по названию

Популярные бренды