Labrie MINIMAX Скачать руководство пользователя страница 52

Страница: 52 / 174

General Maintenance

10.

Turn on the engine and engage the hydraulic system (P

UMP

switch activated).

11.

Fully retract the packer and press the green P

ACK

button to start a complete cycle and test the

efficiency of the limit switch.

OTE

Repeat this procedure until you achieve the proper settings for the limit switch.

Adjusting Tailgate Unlocked Proximity Switch

INIMAX

™ vehicles are equipped with a tailgate proximity switch located on the back left-hand side

body corner. When the tailgate is being unlocked (see Figure 3-26), the cylinder pushes the plate
downward which triggers the proximity switch. This switch then activates the backup alarm and a
warning buzzer inside the cab.

When the tailgate is being locked, the plate goes upward (see Figure 3-25). As the proximity switch is
no more triggered by the plate, the warning buzzer and the backup alarm stop sounding.

Figure 3-25 Tailgate proximity switch (locked position)

Caution

Make sure the ball valve on the suction line is fully open before starting the vehicle.

Warning!

Ensure that no one is standing behind or near the tailgate when adjustment procedure is
carried out.

Plate

Proximity

switch

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Бренды по названию

Популярные бренды