Labrie MINIMAX Скачать руководство пользователя | Manualshive

Страница: 58 / 174

background image

50

General Maintenance

If the arm is still operative despite of the fact that the upper door is fully closed, an adjustment of the
fully closed upper door limit switch is required.

Figure 3-32 Fully closed upper door limit switch

N

OTE

:

In Ontario, provincial regulations require the use of this limit switch.

If installed, this switch is located on the right front side post.

To adjust the fully closed upper door limit switch:

1.

Unscrew the lever adjustement screws of the limit switch (see Figure 3-30).

2.

Raise or lower the detection lever a little bit and tighten up the screws.

The detection lever must touch the inside of the upper door for the switch to be triggered.

3.

Test the operation.

The automated arm should not be working when the upper door is fully closed.

4.

Repeat the adjustment procedure if need be.

Adjusting Arm Stowed Limit Switch

The arm stowed limit switch turns on the A

RM

E

XTENDED

warning light on the dashboard

(see Figure 3-35) when the operator extends the arm or closes the gripper. If this limit switch is
misaligned, the warning light on the dashboard may continue to flash even if the gripper is fully open
and the arm is fully retracted. The arm stowed limit switch also activates an audible alarm when the
arm is out and the vehicle speed is greater than about 3

mph

(5

km/h).

«
...
56
57
58
59
60
...
»

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MINIMAX

Бренд: jcb Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды