manualshive.com logo in svg

Labrie MINIMAX, Руководство по обслуживанию

Поделиться
Скачать
Labrie MINIMAX Скачать руководство пользователя страница 167

Lifting Arm

159

Inspecting the Auto-Closing System

To inspect the system:

1.

Make sure that the vehicle is parked on safe and level ground.

2.

Secure the area around the path of the arm with barrier tape or barricades.

3.

Start the engine and engage the hydraulic pump.

4.

Lower and fully open the gripper.

5.

Close the gripper a few inches (to release the limit switch) and lift the gripper to see if it closes 
automatically.

Auto-Packing

The auto-packing control switch (see Figure  3.11 in the Operator Manual) enables the packer to 
automatically start cycling about four

 

seconds after the gripper is closed. This gives the arm enough 

time to reach the hopper and dump the cart before the packer starts to pack.

When the auto-packing feature is used simultaneously with the multi-cycle system, the packer will 
perform the preset number of cycles (default setting is  3) and then will stop until the operator closes 
the gripper again. When he does, the multi-cycle function is reset and another set of cycles begins.

If the gripper closes in the middle of a packer cycle, the packer will interrupt its current cycle, return 
to its fully retracted position, and restart the next cycle. When a cycle is interrupted and the packer 
has returned to its home position, there is no delay before the packer restarts the next cycle. The four-
second reset will apply only when the packer has completed all its cycles (two

  to eight) and when it 

has returned to its fully retracted position.

Interrupting a cycle prevents carts from emptying directly over the packer. Piled material over the 
packer could reduce its efficiency.

A blue lighted switch means that the corresponding feature is disabled.

A green lighted switch means that the corresponding feature is enabled.

N

OTE

:

The gripper does not need any adjustment. An adjustment rod installed on the back side of the 
gripper allows both gripper blades to move symmetrically (see Figure 10-8).

Danger!

Always lock out and tag out the vehicle when inspecting or performing maintenance on 
it (see 

Locking Out and Tagging Out the Vehicle

 on page

 20).

Danger!

Do not stand directly in the path of the arm while carrying out these adjustments.

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды