Labrie MINIMAX Скачать руководство пользователя | Manualshive

Страница: 105 / 174

background image

Hydraulic System

97

Detecting Cylinder Internal Leaks

An internal leak is caused by a damaged seal inside the hydraulic cylinder (see 1 in Figure 5-25).
Because the cylinder is leaking oil inside (bypassing), a certain amount of pressure is lost, reducing
the efficiency of the cylinder and its capacity to push and/or pull.

If the packer cylinders are bypassing, the seal inside the cylinder may need to be replaced.

To detect internal leaks in packer cylinders:

1.

Apply all safety measures, and set the parking brake.

2.

Pull on the red emergency S

TOP

button.

3.

Start the engine and engage the hydraulic pump.

4.

Fully extend the packer cylinders and disengage the hydraulic pump.

5.

Disconnect the packer extend proximity switch. This prevents the packer from returning to its
initial position.

6.

Disconnect hose “A” and install a plug at the end of it.

7.

Engage the hydraulic pump.

8.

Push the green button and see if oil is leaking from port “A”, then push the emergency S

TOP

button.

If oil leaks out of port “A” when pressure is applied, there might be an internal leak; replace or
repair the cylinder.

«
...
103
104
105
106
107
...
»

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MINIMAX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды