Labrie MINIMAX страница 98 Скачать руководство пользователя

Страница: 98 / 174

Hydraulic System

Figure 5-18 Flow divider

Emptying the Hydraulic Tank

To empty the hydraulic tank:

Prepare the vehicle:

1 a.

Apply the parking brake

1 b.

Start the engine

1 c.

Engage the hydraulic pump

1 d.

Retract all cylinders (packer, crusher panel, tailgate, etc.)

1 e.

Raise the body and install the safety prop

1 f.

Disengage the hydaulic pump

1 g.

Stop the engine

Lock out and tag out the vehicle (see

Locking Out and Tagging Out the Vehicle

on page 20).

Close the ball valve on the succion line (see Figure 2-13).

Disconnect the succion line from the pump.

Place a clean container (minimum capacity: 60

gallons) under the disconnected end of the

succion line to empty the hydraulic tank.

Open the ball valve to let the oil flow into the container.

When the bulk of the oil has been emptied from the tank, remove the drain plug (see Figure
5-19) to allow the rest of the oil drain from the tank.

Place a small container under the plug.

Once the tank has been completely emptied, replace the drain plug and reconnect the succion
line to the pump.

Quick-connect coupler

Rubber Cover

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Похожие инструкции для MINIMAX

Бренды по названию

Популярные бренды

Labrie MINIMAX, Руководство по обслуживанию

Результаты поиска

Содержание MINIMAX

Отзывы:

Похожие инструкции для MINIMAX

Бренды по названию

Популярные бренды