Labconco Logic+ A2 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 201

background image

132

Changing the Optional UV Lamp

The UV Lamp is an optional feature and may not be found on all models.

For optimum performance, the UV lamp should be changed as indicated by the UV
lamp hourmeter found on the LCD Display in the

Settings

submenu.

The UV lamp and the work area of the cabinet must be thoroughly decontaminated
before removing the lamp.

1. Start the cabinet blower and let it operate for 5 minutes.

2. Raise the sash to its full open position.

3. Thoroughly surface decontaminate the UV lamp and the work area of the

cabinet.

4. Unplug the cabinet from all electrical power.

5. Remove the UV lamp by rotating it 90 degrees and lifting it straight up and out of

its sockets.

6. Install new lamp by reversing the removal procedure.

7. Reset the UV Hourmeter as follows:

In the

Settings

submenu enter

UV Parameters

, then select

Reset

, press

[OK/MUTE]

. The hour text will begin to flash, hold

[OK/MUTE]

for 3 seconds.

THE UV LAMP IN THIS PRODUCT CONTAINS MERCURY

Manage in accordance with local disposal laws. DO NOT place lamps in trash.
Dispose as a hazardous waste. For information regarding safe handling,
recycling and disposal, consult www.lamprecycle.org

CETTE LAMPE (UV) DANS CE PRODUIT CONTIENT DU MERCUE

Éliminez ou recyclez conformément aux lois applicables. Pour de l‘information
concernant des pratiques de manipulation sécuritaires et l’élimination sécuritaire
et le recyclage, veuillez consulter www.lamprecycle.org

Reset

UV

Parameters

«
...
130
131
132
133
134
...
»

Содержание Logic+ A2










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Logic+ A2

Бренд: GALLERY Страницы: 18

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: jablotron Страницы: 2

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: York Fitness Страницы: 36

Бренд: Labnet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды