Labconco Logic+ A2 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 201

background image

117

Blower/Motor Replacement

The motor(s) in the biosafety cabinet are ECM, brushless DC motors with extremely
high reliability.  It is rare for the motor to fail.  If the blower(s) fail to start, check all
possible causes first.  The most likely cause for blower failure is a loose wire
connection.  Another reason for accessing the blower/motor is a foreign object caught in
the blower wheel, or the blower wheel is out of balance.

The blower/motor assembly on a biosafety cabinet will be contaminated with
biohazardous material.  Always assume the blower/motor is contaminated, even if you
are told the biosafety cabinet has not been used.  For your safety, take all necessary
precautions before opening the blower/plenum cover, including: gaseous
decontamination of the biosafety cabinet, proper breathing, eye, and skin protection
from biohazards.

Type A2 (8, 9, 10-inch sash) & B2

If replacing a blower/motor assembly, the motor must be programmed at Labconco.
The blower/motor assembly must also be balanced by Labconco, and therefore it is
strongly recommended to replace the blower/motor assembly, never the motor or
blower individually.  Failure to replace the blower/motor with a genuine Labconco
assembly will result in failed or incorrect operation, which can jeopardize the protection
the biosafety cabinet provides the operator, product, and lab environment.

Blower/motors can be awkward to handle, and the blower wheel may contain sharp
edges.  Use safe lifting techniques when removing and replacing the blower/motor.
Always wear gloves and eye protection when handling a blower/motor assembly.

1. Thoroughly and properly decontaminate the biosafety cabinet.

2. Remove the front dress panel as described earlier in this section under

Removal

of External Dress Panels

. Unplug the power cord to this biosafety cabinet.

3. Loosen all of the Phillips screws around the perimeter of the blower/plenum

cover. Remove all screws except two along the top edge of the cover. This will
support the cover. The sash stop bracket is held in place by two of the
blower/plenum cover screws. Remove this bracket.

4.

A2 ONLY:

Release the damper seal (Figure 12-26) by pulling the outside edge of

the seal towards the bolt at the center, and then push the cover inside the
blower/plenum cover (Figure 12-27).

B2

– Skip Step 4, proceed to Step 5.

«
...
115
116
117
118
119
...
»

Содержание Logic+ A2










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Logic+ A2

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Faderfox Страницы: 8

Бренд: XM Fitness Страницы: 10

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Ocean Sonics Страницы: 45

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: ZacUrate Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды