Labconco Logic+ A2 Скачать руководство пользователя страница 182

Страница: 182 / 201

182

4. Install the UV ballast with the hardware (two screws, washers and nuts) provided

in the kit. See Figure 19-1 for reference.

5. Install the relay as shown in Figure 19-1, and secure it with the hardware

provided in the kit.

6. Identify the four circuit wire connectors described below, remove the protective

black cover from each connector with a utility knife, and wire the relay.

Relay Coil: 35-RED & 33BC-BLU (no orientation sensitivity)
NO (normally open): 25-ORG
COM (common): 3E-BLK

7. Connect the UV ballast into the electronics module wiring harness as described

below:

UV Ballast Wires
White wire

2E-WHT

Black wire

25-ORG

Red wires

16-RED & 17-RED (no orientation sensitivity)

Yellow wires

18-BLU & 19-BLU (no orientation sensitivity)

8. Reattach the electronics module to the top of the biosafety cabinet and tighten

the three acorn nuts.

9. Raise the sash and install the UV lamp by placing the lamp pins into each socket,

pressing down on the UV lamp (gently), and then rotating the lamp 90 degrees to
lock it in the lamp sockets.

10. Lower the sash to the fully closed position. Restore electrical power to the

biosafety cabinet.

Содержание Logic+ A2










































































































































































































Результаты поиска

Содержание Logic+ A2

Отзывы:

Похожие инструкции для Logic+ A2

Бренды по названию

Популярные бренды

Labconco Logic+ A2, Техническое руководство

Результаты поиска

Содержание Logic+ A2

Отзывы:

Похожие инструкции для Logic+ A2

Бренды по названию

Популярные бренды