KYMCO Downtown 300i ABS Скачать руководство пользователя страница 95

Страница: 95 / 263

8. DRIVE AND DRIVEN PULLEYS/

V-BELT

8-7

Downtown 300i ABS

CLUTCH/DRIVEN PULLEY
DISASSEMBLY

Hold the clutch/driven pulley assembly with
the clutch spring compressor.
Set the tool in a vise and remove the clutch
drive plate nut.

Clutch Spring Compressor E053
Fittings & Nut Wrench, 41mm E033

Loosen the clutch spring compressor and
disassemble the clutch/driven pulley
assembly.
Remove the seal collar.

Pull out the guide roller pins and guide rollers.
Remove the movable driven face from the
driven face.

Remove the oil seal from the movable driven
face.

ASSEMBLY

•

Be sure to use a clutch spring
compressor to avoid spring damage.

＊

Guide Roller Pin

Oil Seal

Special

Clutch/Driven Pulley

Clutch Spring Compressor

Lock Nut Wrench

Movable Driven Face

O-ring

Guide Roller

Содержание Downtown 300i ABS








































































































































































































































































Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Бренды по названию

Популярные бренды