KYMCO Downtown 300i ABS Скачать руководство пользователя страница 211

Страница: 211 / 263

. BATTERY/CHARGING SYSTEM

16-4

Downtown 300i ABS

BATTERY

REMOVAL

The battery is in the battery box below seat.

1. Remove the seat.
2. Remove the met-in box
3. Remove four screws and then the battery

retainer.

4. Pull battery out to expose the terminal

leads

5. Disconnect the negative (-) terminal lead

from the battery first, then disconnect the
positive (+) terminal lead.

6. Remove the battery from the battery box.

BATTERY INSTALLATION

Install in the reverse order of the removal.

VOLTAGE INSPECTION

Remove the battery cover.
Measure the battery voltage by using a
commercially available digital multimeter.

Voltage (20ºC/68ºF):

Fully charged: 13.0 ~ 13.2 V

Insufficient charged: < 12.3 V

When install the battery, first connect
the positive (+) cable and then negative
(-) cable to avoid short circuit.

＊

Screws

(-) Terminal

(+)

Terminal

Содержание Downtown 300i ABS








































































































































































































































































Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Похожие инструкции для Downtown 300i ABS

Бренды по названию

Популярные бренды

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Похожие инструкции для Downtown 300i ABS

Бренды по названию

Популярные бренды