KYMCO Downtown 300i ABS Скачать руководство пользователя страница 110

Страница: 110 / 263

10. A.C. GENERATOR/STARTER CLUTCH

10-2

Downtown 300i ABS

SERVICE INFORMATION

GENERAL INSTRUCTIONS

•

All operations and inspections in this section can be made with the engine installed.

•

Should drain the coolant before removing the right crankcase cover.

•

Be careful not to drain the coolant when the engine temperature is high. (Perform this operation
when the engine is cold.)

•

Drain the coolant into a clean container.

•

Drain the engine oil into a clean container before removing the right crankcase cover.

•

When the right crankcase cover is installed, fill with the recommended engine oil and coolant.
Remember to bleed air from the water hose.

SPECIFICATIONS

Engine oil: SAE 5W/50#

API-SJ above

Engine quality: Synthetic
Oil capacity at change: 1.5 Liter
Coolant capacity:

Radiator capacity:

0.766 liter

Hose with cool coolant:

0.169 liter

Hose with hot coolant:

0.194 liter

Upper limit for reserve tank capacity:

0.590 liter

Lower limit for reserve tank capacity: 0.370 liter

SPECIAL TOOLS

Flywheel puller

E003

Flywheel holder

E021

SPECIFICATIONS

Item

Standard (mm)

Service Limit (mm)

Starter driven gear I.D.

22.026

～

22.045

22.15mm

Starter driven gear O.D.

42.195

～

42.208

41.5mm

TORQUE VALUES

Flywheel nut : 5.5~6.5 kgf-m (58.8 N-m)

TROUBLESHOOTING

Refer to chapter 1 for A.C. generator troubleshooting.

Starter motor rotates but engine does not start

•

Faulty starter clutch

•

Starter motor rotates reversely

•

Weak battery

Содержание Downtown 300i ABS








































































































































































































































































Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Похожие инструкции для Downtown 300i ABS

Бренды по названию

Популярные бренды

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Результаты поиска

Содержание Downtown 300i ABS

Отзывы:

Похожие инструкции для Downtown 300i ABS

Бренды по названию

Популярные бренды