manualshive.com logo in svg

KYMCO Downtown 300i ABS, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Downtown 300i ABS Скачать руководство пользователя страница 245

20

.

 EVAPORATIVE EMISSION CONTROL SYSTEM

     

Downtown 300i ABS

PURGE CONTROL VALVE

REMOVAL

1. Remove the front cover.
2. Disconnect the purge control valve vacuum

tube that goes to the throttle body and the
tubes that go to the air cleaner and charcoal
canister. Remove the charcoal
canister/purge control valve.

INSPECTION

Connect a vacuum pump to the purge control
valve tube that goes to the air cleaner and
apply vacuum pressure of 250mm/Hg. The
specified vacuum must be maintained for one
minute. Replace the purge control valve with
a new one if vacuum is not maintained.

Connect a vacuum pump to the purge control
valve tube that goes to the carburetor vacuum
tube and apply vacuum pressure of 45mm/Hg.
The specified vacuum must be maintained for
one minute. Replace the purge control valve
with a new one if vacuum is not maintained.

To Air Cleaner

Vacuum Pump

To Throttle Body

To Fuel Tank

To Throttle Body

Vacuum Pump

20-4

Purge Control Valve

To Air Cleaner

To Throttle Body

Содержание Downtown 300i ABS








































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды